DISCOVERING ESSENTIAL PLUMBING SKILLS IS ESSENTIAL FOR INSTALLING A BATHTUB

Discovering Essential Plumbing Skills is Essential for Installing a Bathtub

Discovering Essential Plumbing Skills is Essential for Installing a Bathtub

Blog Article

Call Us Today

How do you feel with regards to A Step-by-Step Guide to Installing a Bathtub?


A Step-by-Step Guide to Installing a Bathtub
Mounting a bath tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old tub with a new one is likewise a moderately challenging project. If the old tub is conveniently available, the project can move immediately; if you have to open up a wall to remove the old tub and also place the brand-new bath tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to vacate the old tub and also embeded in the new one. Make certain you have actually qualified on your own for the work as well as are comfortable attempting it. Rather than hiring a specialist to take control of a halfway-completed task, it is far better to take into consideration employing one prior to you start. Opportunities are you may need a specialist plumber to make tube connections.
This write-up will certainly assist you install a new tub in your shower room if you have actually already gotten a new tub and don't require to change the setup of your previous supply of water pipes.
Your devices as well as product checklist need to make up the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Planning for the Setup


    First of all, the sustaining frame supplied with the bathroom needs to be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to make certain that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the taps system to avoid pressure on the bath tub.
    Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the supplied washers.
    Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its last setting.

    Removing Old Touches


    If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted accessibility that is often the instance.
    Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the remaining water that will come from the pipelines. Once the supply pipes have been gotten rid of, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming during this process. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
    Before carrying on to fit the new taps, compare the pipe connections on the old faucets to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.

    Setting up the Bath tub


    Making use of the two wooden boards under its feet, put the tub in the called for placement. The wooden boards are valuable in evenly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little points.
    The following objective is to guarantee that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub up until the level reviews degree.
    To install taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
    Switch on the water and examine all joints and also new pipework for leakages and also tighten them if necessary. Fill up the bathtub as well as likewise check the overflow outlet and the regular electrical outlet for leakages.
    Ultimately, deal with the bathroom paneling as defined in the manufacturer's user's manual. Tiling and securing around the tub must wait till the bathtub has actually been utilized at least once as this will certainly resolve it into its last position.

    Suitable New Touches


    If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipelines.
    If you require to fit a monobloc, after that you will require minimizing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
    Next off, place the tap in the mounting hole in the bath/basin making sure that the washers are in location between the faucet and the sink. Secure the faucet in position with the supplier provided backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The previous type needs to be attached to the tap ends initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been attached.

    Tiling Around the Tub


    In the area where the bath satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to break a rigid seal, causing the water to penetrate the wall surface in between the bath and also the tiling, leading to difficulties with moisture and also possible leaks to the ceiling below.
    You can pick from a variety of coloured sealers to blend in your fixtures and also installations. They are marketed in tubes and also cartridges, and also can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked paper or soft rope. Remember to always fill up the bath tub with water prior to securing, to permit the activity experienced when the tub remains in usage. The sealer can split fairly early if you do not take into account this activity before sealing.
    Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the marketplace. It is advisable to fit the tiles using water-resistant or water resistant glue as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    I stumbled upon that post on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a lookup on the internet. Liked our content? Please share it. Let somebody else locate it. We recognize the value of reading our article about A Step-by-Step Guide to Installing a Bathtub.


    Ensure leak-free homes.

    Report this page